Free download zte mf910 firmware to begin with, it is important to define what a driver is. For example, the terms software is relatively easy to understand for almost every individual but driver and what it stands for well may be complex.
Bus 001 Device 003: ID 19d2:1405 ZTE WCDMA Technologies MSM Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 002: ID 13ba:0018 PCPlay Barcode PCP-BCG4209 Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub usb_modeswitch log. USB_ModeSwitch log from Sun Jan 11 15: Use global config file: /etc/usb_modeswitch.conf Started via upstart Raw args from udev: /1-7 Bus ID for device not given by udev. Trying to determine it from kernel name (1-7).
Use top device dir /sys/bus/usb/devices/1-7 USB dir exists: /sys/bus/usb/devices/1-7 SCSI dir exists: /sys/bus/usb/devices/1-7 Warning: SCSI attribute 'vendor' not readable. Warning: SCSI attribute 'model' not readable. Warning: SCSI attribute 'rev' not readable. Evgenij onegin filjm 1999.
Use interface /sys/bus/usb/devices/1-7/1-7:1.0 ---------------- USB values from sysfs: idVendor 19d2 idProduct 1405 manufacturer ZTE,Incorporated product ZTE Mobile Broadband Station serial ABCDEF bNumConfigurations 1 bConfigurationValue 1 devnum 3 busnum 1 ---------------- bNumConfigurations is 1 - don't check for active configuration Found packed config collection /usr/share/usb_modeswitch/configPack.tar.gz Searching entries named: /usr/share/usb_modeswitch/19d2:1405* Searching overriding entries named: /etc/usb_modeswitch.d/19d2:1405* SCSI attributes not needed, move on. Use overriden config 19d2:1405 from collection /etc/usb_modeswitch.d config: TargetVendor set to 19d2 config: TargetProduct set to 1405 Driver module is 'option', ID path is /sys/bus/usb-serial/drivers/option1! Matched, now switching Command to be run: /usr/sbin/usb_modeswitch -W -D -s 20 -c /etc/usb_modeswitch.d/19d2:1405 -u -1 -b 1 -g 3 -v 19d2 -p 1405 2> Autocad 2007 portable download free pc. &1 Verbose debug output of usb_modeswitch and libusb follows (Note that some USB errors are expected in the process) -------------------------------- Read config file: /etc/usb_modeswitch.d/19d2:1405 * usb_modeswitch: handle USB devices with multiple modes * Version 2.2.0 (C) Josua Dietze 2014 * Based on libusb1/libusbx! PLEASE REPORT NEW CONFIGURATIONS! DefaultVendor= 0x19d2 DefaultProduct= 0x1405 TargetVendor= 0x19d2 TargetProduct= 0x1405 MessageContent='00' NeedResponse=0 Success check enabled, max. Wait time 20 seconds System integration mode enabled Use given bus/device number: 001/003. Look for default devices.
Bus/device number matched found USB ID 19d2:1405 vendor ID matched product ID matched Found devices in default mode (1) Use interface number 0 -------------------------------- (end of usb_modeswitch output) USB dir exists: /sys/bus/usb/devices/1-7 All done, exit lsusb -v. Modem Port Scan: S0 S1 S2 S3 S4 S5 S6 S7 Modem Port Scan: S8 S9 S10 S11 S12 S13 S14 S15 Modem Port Scan: S16 S17 S18 S19 S20 S21 S22 S23 Modem Port Scan: S24 S25 S26 S27 S28 S29 S30 S31 WvModem: Cannot get information for serial port. TtyUSB0: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud ttyUSB0: ATQ0 V1 E1 -- failed with 9600 baud, next try: 9600 baud ttyUSB0: ATQ0 V1 E1 -- and failed too at 115200, giving up.
Sorry, no modem was detected! Is it in use by another program? Did you configure it properly with setserial? Please read the FAQ at Offline.